research service
Statistical Analysis
Need help analysing laboratory results? Get professional statistical support.
Analyse Results →
Laboratory test listing
Analytical
trending Code: TST5DC298E3
X-ray Powder Diffraction (XRD)
Lab: Allschoolabs · 7 day(s) estimated delivery · 28 views
Test price
Discount for partners
₦18,000
Estimated turnaround7 days (Express testing available)
Sample requirement2g or lesser
Sample submissionPickup from your location / Drop-off at a collection centre
How to Request Test
- Add Test to Cart.
- On the Cart / “Pay & Book Test” page, fill in your details.
For questions, please
.
We maintain strict confidentiality. We do not fabricate, alter, or manipulate results.
About X-ray Powder Diffraction (XRD)
The XRD Rigaku MiniFlex 600 XRD Diffractometer was powered and from the panel, the voltage and current were set at 30kV and 15 mA. The temperature was set at 21-23oC. The computer system was switched on and the software of XRD, TUMI was double clicked to run. The settings dialogue was clicked and all the required setting of power and temperature were checked to correspond to that of the XRD. The analyzed material was finely ground, homogenized, and average bulk composition is determined. The powdered sample was then prepared using the sample preparation block and compressed in the flat sample holder to create a flat, smooth surface that was later mounted on the sample stage in the xrd cabinet.
Sample was poured into the sample holder and then placed in the sample chamber column. Then the door was shut and confirmed from the computer. The sample was analysed using the reflection-transmission spinner stage using the Theta-Theta settings. Two-Theta starting position was 4 degrees and ends at 75 degrees with a two-theta step of 0.026261 at 8.67 seconds per step. Tube current was 40mA and the tension was 45VA. A Programmable Divergent Slit was used with a 5mm Width Mask and the Gonio Scan was used.
Sample & Submission Guide
Sample amount / volume
2g or lesser
How to package the sample
For Liquid samples, per analysis, measure 5ml
Measure 2grams per analysis for solid samples
Liquid samples should be sent in sample bottles, pet bottles, or any air-tight container.
Solid samples should be sent in zip lock bags, sample bottles, or any air-tight container.
Samples should be labeled legibly with paper tape, marker, or writing pen.
Labels should be short and precise (not more than 3 words).
All samples must be strapped together and secured in a bag prior to transport.
Write the Following on the Bag, or Envelope “Allschoolabs Analysis – Receiver: Madison, 08163383206” then add the address of whichever collection center you are sending to.
Measure 2grams per analysis for solid samples
Liquid samples should be sent in sample bottles, pet bottles, or any air-tight container.
Solid samples should be sent in zip lock bags, sample bottles, or any air-tight container.
Samples should be labeled legibly with paper tape, marker, or writing pen.
Labels should be short and precise (not more than 3 words).
All samples must be strapped together and secured in a bag prior to transport.
Write the Following on the Bag, or Envelope “Allschoolabs Analysis – Receiver: Madison, 08163383206” then add the address of whichever collection center you are sending to.
How to submit or send the sample
- Pickup from your location
- Drop-off at a collection centre
Current pickup areas: Any Park around Ojuelegba - Yaba (Lagos, Nigeria), Any Park around Ota (Ogun State, Nigeria)
Collection centres: 104 Western Avenue; Suite C1, God's promise complex, Bells bus stop, Ota
Sample retention
21 Days
Laboratory operating hours
Mon 3 - Fri 2
Other important instructions
For XRD, if you can , please give us your compounds of interest so that we can match with such compounds
Questions About X-ray Powder Diffraction (XRD)
How much does X-ray Powder Diffraction (XRD) cost?
The test price is ₦18,000. The amount shown on this page is the current test price before any eligible discount, delivery or collection charge.
How long does X-ray Powder Diffraction (XRD) take?
The current estimated result delivery time is 7 days. Actual timing can depend on sample condition, preparation and laboratory workflow.
How much sample is required for X-ray Powder Diffraction (XRD)?
The sample requirement shown by the laboratory is: 2g.
How should I package a sample for X-ray Powder Diffraction (XRD)?
For Liquid samples, per analysis, measure 5ml Measure 2grams per analysis for solid samples Liquid samples should be sent in sample bottles, pet bottles, or any air-tight container. Solid samples should be sent in zip lock bags, sample bottles, or any air-tight container. Samples should be labeled legibly with paper tape, marker, or writing pen. Labels should be short and precise (not more than 3 words). All samples must be strapped together and secured in a bag prior to transport. Write the Following on the Bag, or Envelope “Allschoolabs Analysis – Receiver: Madison, 08163383206” then add the address of whichever collection center you are sending to.
How can I send or submit my sample?
Allschoolabs currently accepts sample submission by Pickup from your location or Drop-off at a collection centre. Pickup areas currently listed in the booking database include Any Park around Ojuelegba - Yaba (Lagos, Nigeria), Any Park around Ota (Ogun State, Nigeria). Available collection centre information includes 104 Western Avenue; Suite C1, God's promise complex, Bells bus stop, Ota. Click the "Add to cart" button to continue booking and enter sample details.
Comments & Questions (0)
Quick Booking
Book this test, request pickup/drop-off, or ask the lab a question before payment.
Browse More TestsWhat can you do with your results next?
These are optional related services. The appropriate next step depends on your project objective, methods and available data.
research service
Research Consultation
Discuss the next technical step with a research specialist.
Get Consultation →research service
Scientific Figures & Charts
Turn suitable research outputs into clear figures for reports or publications.
Create Figures →